360 Ford Engine Rebuild Custom Classic Trucks Magazine

360FordFEEngine08202019 Motor Mission Machine and Radiator


Taking a vintage Ford 360 FE big-block and deciding whether to rebuild it with Edelbrock parts or replace it with a newer engine.. Deciding whether or not to rebuild a 1968 Ford F-100 360-cube.

Ford 360 Firing Order Diagram Wiring and Printable


1 - Set timing at about 12* @ ~800 rpm with vacuum advance removed and plugged. 2 - Turned mixture screws out until vacuum gauge read "0" at carburetor port. 3 -With vacuum advance still disconnected I moved the gauge to manifold vacuum port and ran the mixture screws in to see what effect they had on vacuum.

1969 Ford 360 horsepower


#1 ยท Dec 26, 2015 Looking for help with my F100 360. Today I took it for a drive and everything was doing OK. Then on the way back it started stalling out when I would slow down to stop or just take my foot off the pedal to coast. It would start right back up but stall again if I didn't give it a lot of gas.

Ford 360 Engine for sale 88 ads for used Ford 360 Engines


Unless of course parts were changed - and after 50 years that is very very possible. There never was a 360-4bbl, so if its a 4bbl intake then at least SOME parts were swapped. It depends on your plans and how bad you want to know - as stated it could be 352-360-390-410-428 or one of those bored out already.

FORD 360/390 COMPLETER MOTOR Engine Online Auctions


1. Pulling hard and sharp to the right randomly only at night while on a well painted road? This one worry's me. 2. Keeping the truck more on the right side line than in the middle of the lanes. 3. Randomly deactivating itself on a good painted road, no breaks in the lines.

Engine & Cylinder Head Rebuilding, Boonton New Jersey, Machine Shop Boonton


Re: Ford 360 problems. by carnuck ยป Thu Mar 10, 2016 2:14 pm. Double check the size of the oil pump drive from the distributor. High mileage wears them and aftermarket metric sizes them so they end up slipping and not driving the pump. There was 2 sizes of drives from the factory too in different years. Mobius2014.

Ford 360 Firing Order Diagram Wiring and Printable


The 360FE is a great engine though underpowered when stock, as for the 400 it came around during the smog era 70s so it's down on power and in some cases Ford used it in applications that should have got the 460 such as 1ton trucks. The 400 with its long 4" stroke has great performance potential when built correctly.

Ford 360 Engine for sale 74 ads for used Ford 360 Engines


The 360 cubic inch (or 5.9 L) V-8, came out in the 1968 model year and was used as the standard motor in many F-series pickups and trucks. It was a de-stroked 410 motor with a 4.05 inch (102.87 mm) bore and a 3.5 inch (88.9 mm) stroke "" same stroke as the antecedent 352 engine.

Arriba 103+ Foto Diferencia Entre Motor 318 Y 360 Lleno


1967 - 1972 F-100 & Larger F-Series Trucks - Engine problems. FE360 - I have started a thread on the engine forum, but I thought I would post a link here too in case someone here doesn't look there, and maybe has a good idea as to what I should do

Ford 360 Firing Order Diagram Wiring and Printable


The Ford 360 engine is a V8 engine created between 1968 and 1971 with two barrels had 215 horsepower at 4,400 rpm and a max torque of 327 at 2,400 rpm. The later model, which ran from 1972 until 1975, had 196 horsepower at 4,000 rpm and 327 max torque.

Ford 360 Engine for sale 84 ads for used Ford 360 Engines


Because of the quality and popularity of Ford trucks, the 360 remains a popular engine for truck enthusiasts who maintain any number of the fifth and sixth generation Ford F-Series. Share via: Engine Specifications 1968-1971 Ford 360 with 2-Barrel Max Brake Horsepower: 215 @ 4400 rpm Max Torque: 327 @ 2400 rpm Stroke: 3.5 Bore: 4.05

Ford 360 engine with GM HEI run test. YouTube


360 engine problems I have a '75 F150 with a 360 in it. I've had it for a couple months. It had been sitting for 7 years and started on occasion. I had it towed home and besides a manifold and exhaust leak it ran fine until a week ago. I added dual pipes when I fixed the leaking passenger side manifold.

360 Ford Engine Rebuild Custom Classic Trucks Magazine


1 2 Next jasonm2131 New Member Posts: 20 Joined: Sun Nov 22, 2009 11:12 am Location: Granger, IN Ford 360 problems by jasonm2131 ยป Sun Nov 22, 2009 11:26 am Hello Fordification, I have been a long time reader and I finally registered which I should of done awhile ago.

360 Ford Engine Rebuild Hot Rod Network


Because we're dealing with four-cycle engines, the crankshaft turns 720 degrees for every power cycle-two complete 360-degree revolutions. Each valve opens once in those 720 degrees of rotation.

Ford 360 Engine Diagram SchematicSmell Wiring and


#1 ยท Oct 3, 2005 I am looking at a good Ford F350 to put into service with my landscape company. It has a 360 V8. I've heard they are gas hogs. But, how much of a gas hog, I'm not sure of. How would that mileage compare to say a 390 V8 in the same size truck? Or how does it compare to a 302 in an F150? Save Share Reply Sort by Oldest first 1 2 G

360 Ford FE Engine & Cylinder Head Machine Work & Complete Engine


360 engine trouble hi, I just came across a problem with the 360 engine in my truck. I just put a new 2 barrel carburator on pickup, and just got done with the long bed to short bed conversion when i drove down the street and almost cried.

Scroll to Top